How do roofers calculate shingles for a roof?
They break the roof into flat planes, measure each one along its slope and add them up. That total, counted in squares, is the roof's size. The roofer then adds a waste allowance for cutting and fitting, and works out the trim that is bought by length: starter strips along the eaves and rakes, and ridge caps along the ridges and hips.
That list becomes the quote. Shingles, underlayment and labor are usually figured by the square, and the trim pieces by the foot.
What is a roofing square?
A square is the roofer's unit of area: 100 square feet of roof surface. It is measured on the slopes, not on the floor plan. A sloped roof covers more surface than the flat footprint under it, and the overhangs past the walls add more, so the square count cannot be read off your home's listing.
Shape matters as much as size. A simple roof with two slopes is quick to measure and to cover, while one with hips, valleys and dormers has more planes, more edges and more cutting.
How much does a bundle of shingles cover?
Shingles come in bundles small enough to carry up a ladder. Most common shingles are packed so that three bundles cover one square, and some heavier architectural lines take more bundles per square. The wrapper on each bundle says how much it covers, and roofers order whole bundles, rounding up.
Starter strips and ridge caps often come in bundles of their own, sold by the length they cover, so a roof with long eaves and many hips needs more of them. See architectural or 3-tab shingles for how the two common kinds compare.
How do you figure roof pitch?
Pitch is how steep a roof is, written as rise over run: how many inches the roof climbs for every 12 inches it runs level. A roof marked 6/12 climbs 6 inches over each 12 inches of run. The higher the first number, the steeper the roof.
There is no need to climb up to find it. A roofer can read the pitch with a level and a tape on a rafter in the attic, from the ground with a pitch gauge or a phone app aimed at the gable, from the house plans, or from an aerial measurement report. Pitch changes the count because a steeper roof has more surface over the same footprint.
Why does a steep roof cost more?
A steep roof is slower and riskier to work on. Past a certain pitch, a crew cannot stand on the roof safely without harnesses, roof jacks and boards to brace against, and every bundle has to be carried and set with more care. The steeper roof also has more surface, so it takes more of everything.
Many roofers add a charge per square once a roof passes a set steepness, and a taller house adds to it, since materials and debris travel farther. Ask where your roofer's steep charge starts, and whether your roof is past it.
Why does waste get added for hips and valleys?
Shingles are straight strips, and few roofs are plain rectangles. At every hip, valley, dormer and skylight, shingles get cut to fit, and the offcuts often cannot be used anywhere else. Roofers add a waste allowance on top of the measured squares for that: smaller on a simple roof, larger on one that is cut up with hips and valleys.
Edges are counted too. Drip edge, starter strips and ridge caps are measured in running feet along the eaves, rakes, ridges and hips, so a roof with long edges needs more trim for its size.
What about the old layers coming off?
Tear-off is measured over the same area as the new roof, so the square count sets that part of the price too. Each extra layer of old shingles adds to it, and a roofer can usually count the layers at the roof's edge without pulling anything up. Ask how many layers they found, and make sure that count is written on the quote.
How do roofers take the measurements?
There is more than one way, and many roofers check one method against another:
- From the ground: measuring the walls and the eaves, counting the slopes and reading the pitch with a gauge or a phone app.
- From plans: house plans or a builder's drawings show the roof's shape and pitch, when you have them.
- From an aerial measurement report: many roofers order a report made from aerial or satellite photos that lists each plane, its pitch and the length of every ridge, hip, valley and eave. Trees over the roof can hide parts of it from the camera.
- From drone photos: some roofers fly a drone to measure the roof and photograph its condition in the same visit.
- On the roof: a roofer may measure by hand with a tape when the roof is safe to walk.
None of it needs you on the roof. If you have house plans, hand them over, since they can help a roofer check the numbers.
What does a measured roof mean for the price in Georgia?
These are estimates from what Georgia roofers publish, not quotes, and we do not name any company. The per-square-foot ranges are for roof surface, so pair them with the measured roof, not the home's living space.
- Asphalt shingles, installed: estimated at $5 to $7+ per sq ft, or $500 to $700+ per roofing square. See what a shingle roof costs.
- Tearing off the old roof: estimated at about $2 per sq ft, or about $200 per roofing square. See what a roof tear-off costs.
- Full roof replacement, whole job: estimated at $10,900 to $15,000+ for a typical home. See what a new roof costs.
Because both the shingle price and the tear-off price grow with the squares, a measurement that is off by a little moves the whole quote.
What should you ask about the measurement?
- How many squares did you measure, and does that include waste?
- What pitch is the roof, and is there a charge for steepness?
- How many layers are coming off, and how did you check?
- Did you measure from the ground, from plans, from a report or on the roof?
- If another roofer's square count is different, can you walk me through yours?
When two quotes are far apart, line up the square counts first. A different measurement can explain much of the gap before you compare anything else.
Prices mentioned here come from our Georgia roofing cost ranges, built from the prices and cost guides Georgia roofers publish on their public websites, collected September 2026.