Where is the main water shut off valve?
Follow the water line. The main valve sits where the line from the street comes into the house, usually on the side that faces the street. Where you find it depends on how the house is built:
- Slab homes: often in the garage, near the water heater, in a utility closet or on an outside wall near a hose spigot. In some, the only valve is the one out at the meter.
- Crawl space homes: often just inside the crawl space near the front of the house, or on the pipe where it rises through the floor.
- Homes with a basement: usually low on the front wall, where the pipe comes through the wall or up through the floor.
If you had a home inspection when you bought the house, the report may name the spot. Once you find the valve, tag it, keep the path to it clear and show everyone in the house where it is.
What about the valve at the water meter?
If your water comes from a city or county system, the meter usually sits in a box in the ground near the street, with a valve beside it. That valve usually belongs to the water utility, and it often takes a special key to turn. Call your water utility before touching the valve at the meter. Ask them what to do if you ever need it closed in an emergency, and save their number in your phone.
Which kind of home water shut off valve do you have?
Most main valves are one of two types, and each one turns a different way:
- Ball valve: a lever handle. Give it a quarter turn, so the handle sits across the pipe, to close it. When the handle lines up with the pipe, the water is on.
- Gate valve: a round wheel handle, like the one on many outdoor spigots. Turn it clockwise until it stops to close it, which can take several turns.
Turn either one by hand, slowly and firmly. Old gate valves often stiffen from years of sitting still, so it is worth knowing before an emergency whether yours turns at all. If it will not budge, do not force it with a wrench or a hammer: a valve that breaks can leave you with a worse leak than the one you started with. Call a plumber instead.
Can you shut off the water to just one fixture?
Often, yes, and for a small leak it is the better first move, because the rest of the house keeps its water. Look for these smaller valves:
- Toilet: low on the wall or the floor behind it.
- Sinks: in the cabinet underneath, one for hot water and one for cold.
- Water heater: on the cold water pipe that feeds it, usually at the top.
- Washing machine: behind the washer, where the hoses connect.
- Dishwasher and ice maker: often under the kitchen sink, or behind the fridge for the ice maker.
Most of these close when you turn them clockwise, or give them a quarter turn if they have a lever. If one leaks or will not close, the main valve is your backup.
What if your home is on a well?
A home on a well has no water meter at the street. Its shutoff is usually a valve on the pipe near the pressure tank, where the water line enters the house, and it closes like any other main valve. Switching off the well pump at its breaker also keeps the pump from refilling the lines. The label in your electrical panel, or whoever services your well, can tell you which breaker it is.
What should you do right after you shut off the water?
- Open a faucet on the lowest floor, such as a tub or a laundry sink, or an outdoor spigot, to drain the water left in the pipes.
- Stay clear of outlets, cords and appliances that sit near standing water.
- Take photos of the leak and any damage before you clean up.
- Call a plumber, and say that the water is off and where the leak is.
Once the repair is done, open the main valve slowly. Opening it all at once can bang the pipes, and running a few faucets until the water flows smoothly lets out the air that collected while it was off.
When is the valve itself a job for a plumber?
A main valve that is stuck, drips at the handle when you turn it or will not stop the water all the way needs a plumber. Replacing one usually means shutting the water off at the meter first, so ask the plumber how they will handle that with your water utility.
Call a plumber, too, if your water meter keeps moving while every tap in the house is closed. Water is escaping somewhere, and finding a hidden leak is what leak detection is for.
What does a plumber cost for a leak in Georgia?
These are estimates from what Georgia plumbers publish, not quotes, and we do not name any company. We do not have a Georgia range for replacing a shutoff valve, so these are the closest jobs we do have:
- Plumber service call: estimated at $50 to $75+. See what a plumber's service call costs.
- Water leak detection: estimated at $300 to $400+.
- Pipe leak repair: estimated at $330 to $450+. See what leak detection and pipe leak repair cost.
Shutting the water off fast keeps the damage, and the cleanup, smaller, and it lets the plumber start on the repair instead of the flooding.
Questions to ask your plumber
- Is my main valve in good shape, and will it close all the way?
- Would you replace my old gate valve with a ball valve, and what would that cost?
- Do the shutoff valves at my toilets and sinks still work?
- Are any other old valves in the house worth replacing while you are here?
- Is my water pressure where it should be?
Ask for the type of valve going in and its price on the same written quote, so you know exactly what you are paying for.
Prices mentioned here come from our Georgia plumbing cost ranges, built from the prices and cost guides Georgia plumbers publish on their public websites, collected September and October 2026.