What is engineered hardwood?
Engineered hardwood is a floorboard built in layers. The top layer, called the wear layer, is real hardwood, cut from the same kinds of wood solid floors are made of. Beneath it is a core of thin wood sheets glued together with their grain running crosswise, or of dense pressed wood fiber, often with a backing layer on the bottom.
Either core does the same job: it keeps the board steadier than solid wood as humidity rises and falls. In a core of wood sheets, the trick is the crossed grain. Wood swells and shrinks mostly across its grain, so sheets laid in different directions hold each other in check.
How is solid hardwood different?
A solid board is one length of hardwood from top to bottom, cut with a tongue on one edge and a groove on the other so the boards lock together. Being all wood, it moves more with the seasons than an engineered board does. Boards shrink a little in dry winter air, which can open thin gaps between them, and swell back in a humid summer.
Georgia's muggy summers and drier heated winters make that swing part of life for a solid floor. It is normal, and a good installer plans for it. Steady indoor air, with the heat and air conditioning doing their jobs, is kind to either floor.
Where can each one go?
Installers describe a floor by where it sits against the ground. On grade means at ground level, such as a house built on a concrete slab. Above grade means an upper floor, and below grade means below ground level, such as a basement.
- Solid hardwood is commonly published as a floor for rooms on or above grade, nailed down over a wood subfloor. Makers generally advise against basements and against gluing solid boards straight to concrete, since damp from the ground can make them swell and cup.
- Engineered hardwood is commonly approved on, above and below grade, basements included. Over a slab it is usually glued down or floated over a moisture barrier, depending on the product.
These are the common rules, and each product has its own. Ask your installer what the maker allows for your floor, whether the slab or subfloor gets a moisture test first, and what goes between the concrete and the boards. If you want solid boards over a slab anyway, hardwood floor installation explains what that adds.
Can both be refinished?
Yes, because both are real wood on top. The difference is how much wood there is to sand. Each full sanding takes a thin layer off the face, so a floor can be refinished until the wood above the tongue, or above the core, runs out.
Most solid boards have a good depth of wood above the tongue. With engineered boards, the wear layer decides: a thick one gives real room to sand, while a thin one may take only a fresh coat of finish, with no sanding at all. If you expect to refinish down the road, put the wear layer near the top of your list when you compare engineered boards, and get its thickness in writing.
To tell whether a worn floor needs sanding, a recoat or new boards, see should you refinish or replace your hardwood floors.
How do they look and feel once they are down?
From standing height, a finished engineered floor and a solid one look alike, since the face of each is the same wood. Engineered boards are easier to find in wide planks, because the layered core helps a wide board resist cupping. Solid boards are easier to find unfinished, and an unfinished floor is sanded flat and finished in place, so the boards meet without the small grooves many factory-finished boards have along their edges.
Underfoot, a solid floor nailed to a wood subfloor has a firm, settled feel. Engineered boards nailed or glued down feel much the same, while a floated engineered floor can sound a little hollower.
Still weighing real wood against vinyl? See LVP or engineered hardwood.
What does each cost in Georgia?
These are estimates from what Georgia flooring companies publish, not quotes, and we do not name any company. Each range is per square foot.
- Engineered hardwood, installed: estimated at $10 to $11+ per sq ft. See what engineered hardwood installation costs.
- Solid hardwood, installed: estimated at $10 to $13+ per sq ft. See what hardwood floor installation costs.
- Refinishing hardwood: estimated at about $5 per sq ft. See what hardwood floor refinishing costs.
The engineered and solid ranges overlap, so the species, the grade, the plank width and the work your floor needs move the price more than the choice between the two.
The refinishing range is for renewing a wood floor already in place.
Questions to ask your installer
- Is my floor on, above or below grade, and does the maker allow these boards there?
- If my base is a slab, would you glue, float or build a wood subfloor, and why?
- How thick is the wear layer on this engineered board, and how much sanding does that allow compared with solid?
- Are these boards prefinished, or will they be sanded and finished in my house?
- Will solid boards open small gaps here in winter, and what indoor humidity should I keep?
Get the product, its wear layer and the install method in writing with the price, so the floor you were quoted is the floor that goes down.
Prices mentioned here come from our Georgia flooring cost ranges, built from the prices and cost guides Georgia flooring companies publish on their public websites, collected September and October 2026.